Repairing | Roads and Bridges

Road Patch
Job Mixed Quick Set Highway Repair

MANUFACTURER:

Empire Blended Products, Inc.
250 Hickory Lane C Bayville, NJ  08721
(732) 269-4949 C Fax (732) 269-0497
www.empireblended.com

PRODUCT DESCRIPTION:

ROAD PATCH is a Portland Cement based concentrate which is designed to be mixed with local sand and stone to produce a high quality repair material.  This unique formulation develops high early strength with zero shrinkage and excellent durability. Road Patch meets ASTM C-928 for dry packaged rapid hardening cementitious materials for concrete repair.

USES:

• Repair highways, roads and bridges
  
• Repair parking decks and ramps
  
• Repair commercial concrete floors or any concrete surface

• Economical to use due to utilization of local sand and stone
  
• Sets within 20 minutes
  
• Non-shrink
  
• High compressive, flexural and bond strength
  
• Excellent freeze-thaw resistance

Surface Preparation: 
Mark off damaged areas and make a 2" vertical cut with a masonry saw or other suitable equipment around the perimeter of the damaged areas.  Remove all debris within the cut area, as well as grease, dirt and loose or unsound concrete from areas to be patched.  It is important to have all the damaged areas prepared before mixing the material, because the mixing, placement and finishing should be accomplished in a very short time.  Wet the area to be patched with water, to prevent water from being drawn from ROAD PATCH.  However, do not leave free-standing water in the cavity.

Mixing: 
ROAD PATCH is designed to be mixed in the ratio of 50 pounds ROAD PATCH, 100 pounds of clean, washed silica sand, 100 pounds of clean, washed d" stone and 2 gallons of clean water.  Place all sand, stone and b of the mixing water in a clean mixer.  Add the ROAD PATCH while mixing and mix until the ROAD PATCH has been thoroughly blended in.  Slowly add the remaining water to bring the mix to a good trowelable consistency.  A slump of 4" ‑ 6" is recommended.  Do not mix more material than can be placed in 15 minutes.

Placement: 
Place ROAD PATCH in the repair area and level the mix to the surrounding pavement with an appropriate screeding device.  Allow material to stiffen and finish to desired texture using a broom, brush or trowel.

Curing:
Under normal conditions, ROAD PATCH is self‑curing.  Under hot, windy conditions, a curing membrane may be required to prevent surface dry out.  Allow material to develop strength for at least 1 hour after set before allowing traffic to resume over patched area.

Coverage: 
When mixed in the recommended ratio, one 50 pound bag of ROAD PATCH will yield 2 cubic feet.
Packaging: 
Available in 50 pound multiwall paper bags with moisture barrier and 2,000 pound bulk bags.

Color: 
Light gray

LIMITATIONS:

Do not apply to frozen surfaces or if temperature will fall below 40EF within 24 hours.

CAUTION:

Contains Portland Cement CAS # 65997-15‑1.  Freshly mixed cement products may cause skin injury.  Avoid contact with skin where possible and wash exposed areas promptly with water.  If any product gets into the eye, rinse immediately and repeatedly with water.  If ingested, do not induce vomiting and get prompt medical attention.  Keep Out Of Reach Of Children.

WARRANTY:

Due to the use of this product beyond our control, we assume no liability for damages of any kind, and the user accepts the product "as is" and without warranties, expressed or implied, from either Empire Blended Products or its agents.  The suitability of the product for an intended use shall be solely up to the user.  Our only obligation shall be to replace or pay for any material proved defective, with our liability limited to the purchase price of materials supplied by us.

HOME | ABOUT | PRODUCTS | CONTACT
ARTICLES | LOCATIONS

250 Hickory Lane, Bayville, NJ 08721
Phone: 732-269-4949 | Fax: 732-269-0497
vipcustomer@empireblended.com

Copyright © Empire Blended Products, 2003
Site design by Xtreme Web Creations